Відео

It’s 2024 it’s not 900 bucks!!!

Worthy of note: 5:33 the stock strut bolts are 15mm, not 17, at least on my 1500, but the new ones are 17 mm. Also 7:25 my upper control arm was the opposite of what's shown here, you needed to pry up in this video but I had to pry DOWN a good ways, tough mechanics of prying it down and lifting the floppy control arm assembly upward! Jack stands are DEFINITELY your friend to hold the control arm when disconnecting the ball joint and tie rod!

Thanks for the video . Wear safety glasses next time bro.. protect those eyes especially with all that rust and dirt....

God my bank account and iq are bigger than my ego!

Ride is horrible, cost is high , in my opinion big bill for an ego!

The guy who made the $1600 comment is right , I bet parts manufacturers loved the guy that invented that kit ….. garbage…… nice for young lads who want to look cool for a short time …. Terrible for what ever parent is footing the bill

this is good stuff. This also happens to be the method I used for rough country 2 inch loaded struts for my 2011 GMC Sierra RWD, extended Cab. The key is to remove the knuckle joints and then you everything drops down far enough to stab in the longer strut. One pointer that is worth emphasizing. Take the wheel sensor wiring connector OFF so it does not break under a sudden drop even though you are going to tie the wheel up to prevent it. it's just going to happen that things are going to break and the brake line and the wheel sensor wiring are definitely going to break if the entire wheel assembly drops down. Once the strut is installed, and bolted top and bottom, it is going to be hard to lift the wheel assembly and get the three knuckles back into place. I used a floor jack to carefully life the wheel assembly and at the same time, moving the wheel assembly and the knuckle joints to get them to all move into place at the same time. On my truck the knuckle joints have hex fitting to keep them from spinning while you tighten. One of them is a boxed 10 mm squared end that is used for the same reason. Pay attention to the torque specs and check your work and make sure to put the wheel sensoring wiring connector and the bracket that holds that and the brake line down to the Wheel assembly arm. I applied some anti seize to the hub face so its easier to remove the wheel and tire on my next brake job.

Is there tune if u run headers

Where can I get new seats for all the truck 2014 Silverado , also , can I upgrade the whole front for a newer one

Shop These LED C-Bar Factory Style Headlights! : amtrucks.at/47VRd8x

slight technical advice: when tightening bolts and nut, you want to turn the NUT, and HOLD the bolt. this is mostly for application involving medium to high torque, but is also good standard practice is you are going to be reusing old bolts and nuts. great video.

Where can I purchase those front and rear mud flap delete/ replacement covers I’ve been looking everywhere need them for my truck

Shop These MotoFab Rear Leveling Kit! : amtrucks.at/2Of2x6I

Is the factory muffler stainless steel?

How much would it be if I took it to the dealership...Can 1 person do this?

DOES IT COME WITH FULL ASSEMBLY??

Shop This C&L Single Exhaust System! : amtrucks.at/2ZiJVyc

If this works on a zr2, I’d buy it.

Installed these to try and solve the hyper flash issue in my left tail light and now I have hyper flash issues with both my tail lights…

Shop This Diablosport Trinity 2 EX Platinum Tuner! : amtrucks.at/43hA3zE

Nice scam. Painted stock GM calipers and brackets, Detroit Axle rotors and pads for 4x the price.

The connectors for the bulbs do not have standard chevy connectors. What type or brand of after market leds do I use?

Trust me,trust me, trust me if you’re going to do this please do yourself and favor and go get the Gen5DIY harness kit. This is the worst way to wire it and worst set up of the lights Made. 0/10 would never recommend.

So you didn’t wire the reverse light ?

I thought maybeeee I could do this…. after we hit the 60th different millimeter, I said nahhhh

What is the name of this product? That's badass

Will it work with bose

First purchase needs to be HPtuners and folloe matt staffords 2 videos on tuning the engine and transmissions in these trucks. Night and day difference.

Will it fit a 2014-2015 sierra?

Do you have to do the 3 compressions I have seen in other videos? I'm doing this project so I'm curious.

What brand are the wheels and tires

Is that green a factory color?! It’s beautiful

Does it work on a 3500 ram diesel 2014 dully

Please don't get me wrong, I'm using full MSD ignition on a well modified SB Ford W engine but why would you use MSD coil packs on a stock engine when the OE Delco/Delphi work well? Also, without replacing the plugs and wires, you may have defeated any gains

Is there any actual performance data on what HP / torque gains / lowered intake temps this provides?

That just seems like a lot of money for a four cylinder

Shop These MSD Gen V Blaster Coil Packs! : amtrucks.at/4afJvs2

Badass , price?

Wow that's a good-looking truck that you can drive every day!

Shop This S&B Cold Air Intake! : amtrucks.at/2OndvM4

Can I install with a spacer to give at least 3-4 " lift?

What size is the rear

Shop This Rough Country Dual Exhaust System! : amtrucks.at/3iCrw5N

The calipers are stock Silverado calipers remanned and powder coated red?

Do they fit on 2019 chevrolet trail boss custom 1500 4x4??

Nice instructions

Shop These LED Reflector Headlights! : amtrucks.at/3Rjos0i

Torque specs for tie rod and Upper ball joint would have been nice...

i like the Green Day background music